Forty-seven percent of the United States depends on ground water for their basic drinking water supply. Having a basic understanding about ground water quality will help ensure that your well is supplying potable water for your household.

Along with human activities, water quality is affected by a combination of natural processes. Most relate to chemical compositions underground. However, other factors such as biological, physical, and radiological conditions can affect water quality as well.

The National Ground Water Association recommends that water well owners have their wells checked and tested by a certified and/or licensed contractor every year to ensure water safety. You can find these licensed contractors on Repairfinders.com

Hard Water

The most common problem associated with ground water may be hardness, generally associated with an abundance of calcium and/or magnesium dissolved in the water. Hard water has not been shown to cause health problems, but can be a nuisance as it may cause soap curds and deposits to form on pipes and other plumbing fixtures. Over time, this can reduce the diameter of the pipes.

Calcium and magnesium are found in ground water that has been exposed to certain rocks and minerals, especially limestone and gypsum. When these materials are dissolved, they release calcium and magnesium. Hard water is considered bad for your plumbing, but people with heart or circulatory problems may want to consult their physician about drinking softened water, because the softening process removes calcium and magnesium, and adds sodium to the water.

Iron and Manganese

A “rusty” or metallic taste in water is a result of iron, and sometimes manganese, in ground water. They not only create a bad taste, but they also can stain pipes and clothing.

Iron and manganese are naturally occurring, and most ground water has some amount of dissolved iron and manganese in it. It comes from contact with minerals that contain iron, such as pyrite.

There are several treatment methods. Installing a water softener may help if iron and manganese are present in low quantities and the softener is designed for their removal. Aeration (the addition of oxygen to the water), chlorination, and feeding ozone or hydrogen peroxide can aid in the precipitation of iron, which it is removed from the water by filtration. Potassium permanganate feed with manganese greensand filters, and some recently designed synthetic media, will remove iron and manganese, as well.

Nitrogen

Most nitrogen in ground water comes from the atmosphere. Some plants can “attach” nitrogen from the atmosphere onto their roots. The nitrogen not used by the plants is then released into the soil.

Nitrogen compounds also can work their way into ground water through fertilizers, manure, and urine from farm animals, sewage, and landfills.

The most common forms in ground water are ammonia, nitrate, and nitrite. Nitrates can be especially toxic to children under six months of age. Exposure to ammonia also presents a health risk. It is toxic to aquatic life such as fish, and it interferes with water treatment.

There are a variety of treatment methods to correct this problem, including reverse osmosis systems with water softeners to remove nitrates and nitrites, and oxidation to remove small amounts of ammonia. However, treatment should be a last resort. Removing the source of contamination is the first priority. You should also be sure to protect the area around the wellhead from contamination by animals or fertilizers.

Silica

Silica comes from the weathering of silicate minerals in the ground. It causes no harmful effects to humans, but large amounts can cause scaling in pipes that impacts water flow, and it can interfere with iron and manganese removal.

Sulfur

Sulfur can occur in ground water in two forms: sulfides and sulfates. Sulfides are naturally occurring in much of the United States in limestone containing organic materials; ground water affected by oil, gas, and coal deposits; in marshes and manure pits; and in the byproduct of well-established iron bio films. Sulfates often come from the dissolving of minerals, such as gypsum and anhydrite.

A “rotten egg” smell coming from your water indicates the presence of hydrogen sulfide gas. Along with creating an unpleasant odor and taste, sulfides cause corrosion to plumbing and darken water.

There are several methods for treating sulfur. Aeration, ozone, hydrogen peroxide, and chlorine (best followed by filtration) are effective against dissolved hydrogen sulfide or gas. A reverse osmosis system, nanofiltration system, or a negative ion-exchanger also can be effective in reducing sulfates. Filtration is necessary in combating sulfur formation as a mineral or in bio films.

Total Dissolved Solids

TDS, as it is commonly known, is the concentration of all dissolved minerals in water. It is the direct measurement of the interaction between minerals and ground water.

TDS levels above 1000 mg/L will usually yield poor tasting water. Levels above 2000 mg/L are considered undrinkable due to taste, and levels more than 10,000 mg/L are defined as undrinkable.

Water softeners with a reverse osmosis system are effective in lowering the TDS to satisfactory levels.

Additional Treatment Information

For more information on water treatment methods, you should contact a well specialist. There are many listed on Repairfinders.com. All it takes is a moment of your time, and remember that when it comes to something as life sustaining as water, you do not want to hold for tomorrow, what you should do today.

If you own a house, you own a water heater. You probably don’t spend much time thinking about the water heater until, one morning, you go to take a shower and there’s no hot water. Then you probably think about it a lot.

And if you’re the curious sort, the following water-heater question may have crossed your mind: “How can the water stay hot if cold water comes in as soon as you start using the hot water?”

A gas water heater is nearly identical to an electric water heater, except that it does not contain the two heating elements, but instead has a gas burner at the bottom, with the chimney running up through the middle of the tank.

A water heater consists of the following parts.

1.     A heavy inner steel tank that holds the hot water. Typically, this tank holds 40 to 60 gallons. It has to be able to hold the pressure of a residential water system, which typically runs at 50 to 100 pounds per square inch (psi). The tank is tested to handle 300 psi. The steel tank normally has a bonded glass liner to keep rust out of the water.

2.     Insulation surrounding the tank

3.     A dip tube to let cold water into the tank

4.     A pipe to let hot water out of the tank

5.     A thermostat to control the temperature of the water inside the tank (Many electric water heaters have a separate thermostat on each element.)

6.     Heating elements to heat the water (These are the thick electric elements similar to those you see inside an electric oven.)

7.     A drain valve that allows you to drain the tank to replace the elements or move the tank

8.     A pressure relief valve (This is an important safety feature that keeps the tank from exploding.)

9.     A sacrificial anode rod to help keep the steel tank from corroding.

Heating the Water

The thermostat controls the temperature of the water inside the tank. Normally you can set the temperature between 120 and 180 degrees Fahrenheit (49 to 82 degrees Celsius). It is generally recommended that you keep the temperature between 120 to 140 degrees F (49 to 60 C) — especially if there are children living in the house — to prevent scalding. It also saves energy.

Normally, the thermostat is underneath a cover plate and it has a knob or a screw that you can use to set the temperature.

As cold water comes in, it remains at the bottom of the tank because it is denser than hot water. If you use the hot water faster than the heating elements can heat the incoming cold water, and if you consume all of the hot water that the tank holds, you run out of hot water in the middle of your shower. If this seems to happen too often, it could mean that the bottom heating element in an electric water heater has burned out or that your water heater is too small for your house. Or it could mean that you are taking really, really long showers.

If you have any problems at all with your water heater, the best thing to do is to find a qualified professional from Repairfinders.com to look at it. They can quickly find out what the problem is and fix it for you in a timely and cost efficient manner.